Whirlpool WED97HEDW Instrukcja Użytkownika

1W10676165AW10676166A - SPTable of Contents DRYER SAFETY ... 2INSTALLATION REQUI

104-Wire Direct Wire ConnectionIMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections.Dire

111. Prepare your 3-wire cable for direct connection 1"(25 mm) 3½"(89 mm)2. Remove center screwB5. Connect remaining wires4. Connect

12Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center, terminal block screw (B). Ti

13Louvered HoodAngled HoodBox HoodExhaust hoods:Elbows:Recommended Styles: 45° elbows provide better airow than 90° elbows.Clamps: Use clamps to

14The “Vent System Charts” provide venting requirements that will help achieve best drying performance.Special provisions for mobile homes:Exhaust ve

15Install Vent System1. Install exhaust hood12" min.(305 mm)12" min.(305 mm)2. Connect vent to exhaust hoodInstall exhaust hood and use caul

165. Attach long hose to dryer ll valve and tighten couplingRemove protective cap from water inlet valve. Attach other end of long hose to ll val

172. Adjust leveling legsIf dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once

181. Remove door from dryer2. Move the door strike Using a TORX T25® screwdriver, remove the 2 screws securing the door strike to the door frame of t

194. Remove outer window assembly from trim ringUsing a Phillips screwdriver, remove the 2 screws from the outer window retainer and rotate the outer

2DRYER SAFETYIMPORTANT: When discarding or storing your old clothes dryer, remove the door.

208. Reinstall hinge and latch on opposite sidesUsing a TORX T25® screwdriver, reinstall the latch plate, latch backing plate, and hinge assembly on

219. Reinstall inner door assemblyPosition the door with the inside of the door facing up. Reinstall the 10 screws securing the inner door to the out

223. Remove inner door from outer doorPosition the door with the inside of the door facing up. Using a Phillips screwdriver, remove the 10 screws sec

23Reverse door swing square-shaped door1. Remove door from dryerUsing a TORX T25® screwdriver, remove the 4 screws securing the door hinge to the drye

6. Reattach inner door to outer door Position the inner door on the outer door assembly. Using a Phillips screwdriver, secure with the 13 screws rem

3INSTALLATION REQUIREMENTSTOOLS AND PARTSGather the required tools and parts before starting installation.Tools needed:Flat-blade screwdriver #2 Phill

4DRYER DIMENSIONSBack view:61/2"(165 mm)297/8"*(759 mm)31/2"*(89 mm)61/8"*(156 mm)143/8"(365 mm)3/4"*(18 mm)NOTE: Most i

5Installation spacing for recessed area or closet installationAll dimensions show recommended and minimum spacing allowed. Additional spacing shou

6Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m

7For direct wire installations:ELECTRIC INSTALLATIONFor power supply cord installations:Remove hold-down screw and terminal block cover.1. Choose elec

8Power supply cord strain relief:4-Wire Power Supply Cord ConnectionPower Supply Cord Connection4-wire receptacle (NEMA type 14-30R)4-prong plugSpade

93-wire receptacle (NEMA type 10-30R)3-prong plugSpade terminals with upturned endsRing terminals3. Connect remaining wires2. Connect neutral wireCB4.