Whirlpool AKM 260/NB Instrukcja Obsługi Pobierz pdf (Strona 9)

Top 20 mm

Top 30-60 mm

ADJUSTMENT TO DIFFERENT TYPES OF GAS

This operation must be performed by a qualied technician.

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• ThegasnozzlesmustbechangedbyAfterSalesServiceoraqualiedtechnician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience difculty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap

if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Instruction)

• Remove grids (A).

• Extractburners(B).

• Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to

be replaced.

• Replace it with the injector suitable for the new type of gas.

• Re-assemble the injector in (D).

• If you have a multiple crown burner use side spanner to replace the injector (E).

Beforeinstallingthehob,remembertoafxthegascalibrationplatesuppliedwiththeinjectorsin

suchawaythatitcoverstheexistinginformationrelatingtogascalibration.

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:

• tightenscrewtoreducetheameheight(-);

• loosenscrewtoincreasetheameheight(+)

Theadjustmentmustbeperformedwiththetapinminimumgassettingposition(smallame) .

• The primary air of the burners does not need to be adjusted.

• Atthisstage,lightuptheburnersandturntheknobsfrommaxposition to minimum position tocheckamestability.

Uponcompletionofadjustment,resealusingsealingwaxoranequivalentmaterial.

REFERENCE TO LOCAL REGULATIONS

Theinstallationandmaintenanceoftheappliancemustbecarriedoutbyaqualiedskilledtechnicianinaccordancewiththeregulationsinforce,andinparticular:

• Decree of 2 August 1977

TechnicalandSafetyRulesapplicabletofuelgasandliqueedhydrocarboninstallationslocatedwithinresidentialbuildingsandoutbuildings.

• Standard DTU P 45 - 204

Gas installations (formerly DTU no. 61-1 - Gas installations April 1982 + supplement no. 1 of July 1984).

• Departmental Health Regulations

For appliances connected to the mains electricity supply.

• Standard NF C 15-100

Low-voltage electrical installations - Standards.

REFERENCE TO LOCAL REGULATIONS

Theapplianceissuppliedwitha1/2”threadedconicalendtobeconnectedtothegassupply(accordingtoISOregulationsISO 7/1 RP 1/2). The connection must be

effected in accordance with standard NBN D 51-003usingrigidpipingorinaccordancewithspecicationssheetA.R.G.B./03usingexibletubing.Theappliancemust

be installed complete with an AGB-approved stop valve.

AFTER-SALES SERVICE

Before calling the After-Sales Service, make sure you can give the following information:

- type of fault or problem;

- exactmodel(writtenonthelabelafxedtotheinstruction/warranty);

WARNING