Whirlpool EKB 3482/2481 Instrukcja Obsługi

76PRECAUTIONS AND GENERAL SUGGESTIONS PAGE80TABLE OF CONTENTSDESCRIPTION OF THE HOB PAGE77BEFORE USING THE HOB PAGE79HOW TO USE THE HOB PAGE82COOKING

85Display position Suitable for the following cooking12 10 To boil water, cook “gnocchi”, soup10-11 10 To fry potatoes and meat ex. goulash9-10 9-10 T

861. The pans base must be the same or slightlygreater than that of the cooking zone -never smaller.2. Use only pans with thick flat bases.3. Possibly

871. Use clean clothes or paper for domestic use,liquid detergent, commercial products suchas Sidol for stainless steel, Stahlfix or Cera-fix or the e

88You have bought a high quality hob, manufac-tured according to the most advancedtechnologies. In case of faults, please check ifyou have followed al

89Important hintsThis appliance has been designed, builtand marketed in compliance with:- the safety targets of the “Low Voltage”EEC Directive 73/23;-

90ASSEMBLYGLASS CERAMIC HOBS WITHFRAME1- Installation of the hob on stainless steelworking areaTools required:- electric scisor, or profils cutter, ev

91- Locate properly the hole position that youshould make +/- 0.5 mm- The frame of the hob should be able to restproperly on the main top; therefore m

922 - Installation on stone or woodworking tableMake an opening in the worktop following thedimensions, in millimeters, indicated in:- Fig. 1A, for gl

93GLASS CERAMIC HOBS WITHOUTFRAME (EKI 3482, KI 947)1. Mounting on ready surface tolean the hobThe leaning surface in the hole can be madeeither by mi

941.1 Preparation of the workingsurfaceClean the hole from any dust or dirt.- Brush 1 or 2 hands of special primer and dryfor about 30 minutes. This w

77DESCRIPTION OF THE HOBGLASS CERAMIC HOB WITHFRAMEKU 947-11. Quick Star heater ø 180 mm, 1800W - 400V2. Quick Star heater ø 180 mm, 1800W - 400V3. Do

952. Use of the metal lines support(supplied)The leaning area can be also prepared bymounting the metal lines that the height canbe regulated by +/- 1

962.1 Mounting in the hole themetal leans supportsUse the metal leans support as a tool to helpyou locate the position of the screw to fix theflat ecc

973. Glueing of the glass ceramic hobInject in the space around the glass, black sili-cone, avoid air bulbs and remove slightly thesilicone excess.Spr

98Attention: Before glueing with special materi-al (stone, etc.) its necessary to make sure ofthe compatibility of the primer and the mastic.Attention

99To be carried out before the electrical connec-tion to the mains. The appliance must beinstalled by a competent electrician, with allelectrical and

100yellowgreen front rear rear front residual heathearthing left left right right 2 circuits400 VAfter the installation, the electrical components sho

78GLASS CERAMIC HOBS WITHOUTFRAMEEKI 3482-1 / EKB 3482/24811. Double radiant heater ø 210/120 mm,2100/700W - 400V2. Radiant heater ø 145 mm, 1200W - 4

791. Packaging (plastic bags, polystyrene parts,etc.) must be stored out of reach of childrenas they are potentially dangerous.2. The packing material

80Warning: electrical shock hazard1. Before any maintenance operation,disconnect the electricity leading to the hobat the main power supply. Failure t

8110. Do not let electric wires (i.e.: of smallhousehold appliances) to come intocontact with hot parts of the hob.11. Do not forget synthetic clothes

82The cooking zones are circumscribed and visi-ble on the hob surface. The cooking zones arecontrolled by knobs marked 0 to 12 or 10, sit-uated on you

83DUO COOKING ZONEThe second area of both duo cooking zone canbe switched ON by turning the correspondentknob to the right, rotating it at the far end

84WARMING ZONE TOUCH CONTROL(For mod. EKA 3482-1 li and EKA3482-1 re)Cooking Zone/Platt’s heating zoneOn the glass ceramic hob, there is fourcooking z