Whirlpool ADN 109 Instrukcja Instalacji

ICE CUBES MAKERS RangeSPRAY Technology

10 NG MDP 150 CONSUMP. CONSUMP. CONSUMP. NET DIMENSIONS DIMENSIONS GROSS VOLUMEWATER COND.. WATER TOTAL WATER W

11

12 PRODUCTION CHARTS (Kg/Day) NDP20 Tw/Tr 45 40 35 30 25 20 15 10 35 8 10 13 14 16 17 17 17 30 12 15 17 19 20 21 21

13 NG 35 Tw/Tr 45 40 35 30 25 20 15 10 35 14 19 22 26 28 29 30 30 30 21 26 30 33 35 37 37 37 25 27 32 36 39 42 43

14 NG 60 Tw/Tr 45 40 35 30 25 20 15 10 35 24,4 32,5 39,3 44,7 48,7 51,3 52,6 52,5 30 36,7 44,9 51,6 57 61 63,7 64,9 64,8

15 NG 110 NG 150 Tw/Tr 45 40 35 30 25 20 15 10 35 61 81 98 111 121 128 131 131 30 91 112 129 142 152 156

16 DELIVERY & UNPACKING Upon receipt, thoroughly inspect the packing container. If there appears to be damage to the container contact the shi

17 BOXES, ETC.) IN REACH OF CHILDREN.

18 INSTALLATION Required conditions for placement of unit IMPORTANT: The NG machines are intended to work at room temperature between 5ºC and 43ºC an

19 b) WATER WITH MORE THAN 1000 PPM: Ice will be less hard and tend to adhere. Cubes with white spots may appear. Lime deposits may impede proper fun

2 CONTENTS Introduction Warnings...

20 - The Line to base of plug must have a minimum section of 2.5 mm2. - Be sure voltage indicated on rating plate corresponds to that of mains suppl

21 STARTING UP Having followed the installation instructions (ventilation, temperature, room conditions, water quality, etc…), proceed as follows:

22 ADJUSTMENTS Condenser water valve pressostat - This pressostat controls high pressure by opening and closing the condenser water valve. Differen

23 Safety Pressostat This safety device trips when discharge pressure is too high. Pressure might exce

24 MAINTENANCE AND CLEANING INSTRUCTIONS IMPORTANT: Maintenance and cleaning procedures as well as problems derived from failing to carry them out

25 MAINTENANCE AND CLEANING PROCEDURES ** WARNING: Unit should always be disconnected during maintenance/cleaning procedures. Water Condenser 1) Di

26 NOW STARS THE SANITARY CLEANING 9) Connect the machine once it has finished entering water, remove the evaporator cover and pour lye (one gla

27 6) Assemble the filter, nozzles and connecting tube. ATTENTION: IT IS ESSENTIAL THAT SPRAY NOZZLES ARE COMPLETELY PERPENDICULAR TO THE CONNECTING

28 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES SOLUTION A) The machine is not plugged in. A) Plug the machine. B) The line fuse has blown. B)

29 A) Faulty hot gas valve or wrongly connected. A) Verify and change if necessary. B) Low water pressure. B) Increase water pressure if possible.

3 INTRODUCTION Thank you for choosing ITV's NG DP Ice Cube Maker. You have purchased one of the most reliable ice-making products on the market

4 IMPORTANT: - Do not attempt to service this machine yourself. Improper use by other than specially trained technicians is extremely dangerous

5 DESCRIPTION Main features: − Stainless steel body AISI 304 and chapa galvanizada. − Anti-blocking spray nozzles. − Pump without seals. − High press

6 OPERATING PRINCIPLE FOLLOWING THE ELECTRIC DIAGRAM (TIMER ON DEFROST - MICROSWITCHES DEPRESSED). - The ITV model NG has two switches: 1st In the

7 - Air-cooled machines have a fan (R) which is controlled by the pressostat (F). - In water-cooled models without pressostatic valve, pressostat (

8

9 SPECIFICATIONS Models: NDP 20 NG DP 30 - 150.