Whirlpool AKM 202/IX Instrukcja Obsługi Pobierz pdf (Strona 3)

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

• This product can be embedded in a worktop 20 to 40 mm thick.

• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening

in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper

surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you

intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped

with a cooling system. The manufacturer declines all liability if another brand oven is installed beneath the

hob.

• Before installation, make sure that:

- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the

rating plate and injector table).

- The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations.

- Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.

GAS CONNECTION

• The gas supply system must comply with local regulations.

• You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no

information concerning your Country is given, please ask details to your Installer.

• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel

pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying

with local regulations. The maximum length of the hose is 2 linear metres.

• Before connecting the tube to the elbow fitting (A), interpose the

washer (B) supplied, in compliance with EN 549.

For Belgium - replace the elbow connection with the one supplied in the kit.

Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture.

It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy water.

ELECTRICAL CONNECTION

• The electrical connections must comply with local regulations.

• The data relevant to the voltage and power absorption are indicated on the rating plate.

• The earthing of this appliance is compulsory by law.

• The manufacturer cannot be held responsible for any injury to persons or animals or damage to property

arising from failure to comply with these requirements.

• When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm.

• If necessary, the electrical power cable must be replaced exclusively with a power cable having identical

characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F).

This operation must be performed by a qualified electrician.

Earth

(yellow/green)

ADJUSTMENT TO DIFFERENT TYPES OF GAS

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and orange sticker

applied on the top of the hob, change the injectors.

Remove the orange sticker and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• The gas nozzles must be changed by After Sales Service or a qualified technician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

Note: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as

it will go.

Should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the

replacement of the burner tap if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Instruction)

•Remove grids (A).

• Extract burners (B).

• Using a socket spanner of the appropriate size unscrew

the injector (C), unscrew the injector to be replaced.

• Replace it with the injector suitable for the new type of

gas.

• Re-assemble the injector in (D).

• If you have a Triple Crown burner use side spanner to

replace the injector (E).

Before installing the hob, remember to affix the gas

calibration plate supplied with the injectors in such a way

that it covers the existing information relating to gas

calibration.

ASSEMBLY

After having cleaned the perimeter surface, apply the supplied

gasket to the hob as shown in the figure.

Position the hob in the worktop opening made respecting

the dimensions indicated in the Instruction.

Note: the power supply cable must be long enough

to permit its upward extraction.

1. Fit the brackets into the relevant bores and fasten

them by means of their screws.

2. Make an opening in the worktop, respecting the

dimensions indicated in the Instruction.

3. Install the cooktop in the worktop.

1 2 3 4

Komentarze do niniejszej Instrukcji

Brak uwag

Whirlpool AKM 202/IX Instrukcja Obsługi Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Płyty grzewcze Whirlpool AKM 202/IX