Whirlpool TEP 649 L Instrukcja Obsługi Pobierz pdf (Strona 17)

in order to prevent leaks. The seal must always be

replaced after rotating the pipe fitting (seal supplied

with the appliance). The gas supply pipe fitting is a

threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel

pipe to a threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas

cylindrical male attachment.

These pipes must be installed so that they are never

longer than 2000 mm when fully extended. Once

connection has been carried out, make sure that the

flexible metal pipe does not touch any moving parts

and is not compressed.

 Make sure that the hose and the aluminium and

rubber gaskets comply with current national

regulations .

Checking the tightness of the

connection

 When the installation process is complete, check

the pipe fittings for leaks using a soapy solution.

Never use a flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other

than the default type (indicated by the label placed

on the upper part of the hob or on the packaging),

the burner nozzles should be replaced as follows:

1. Remove the hob grids and slide the burners off

their seats.

2.Unscrew the nozzles using a 7 mm socket

spanner, and replace them with nozzles for the

new type of gas (see table 1 Burner and nozzle

specifications).

3. Reassemble the parts following the above

procedure in the reverse order.

4. Once this procedure is complete, replace the old

rating sticker with one indicating the new type of

gas used. Stickers are available from any of our

Technical Assistance Centres.

 Adjusting the burners primary air

The burners do not require primary air adjustment.

 Setting the burners to minimum

1.Turn the valve to the minimum setting position.

2. Remove the knob and adjust the regulatory screw,

Blue

Brown

Neutral

Live

Green/Yellow

Earth

UNDERSIDE OF HOB

Terminal board

On the lower part of the

appliance there is a connection

box for the different types of

electricity supply (the picture is

only an indication and is not an

exact representation of the

purchased model).

Single-phase connection

 The cable supplied should only be used for this type of

installation.

Mains supply characteristics:

Voltage and mains frequency

 220-240 V 1+N ~ 50 Hz

 230 V 2 ~ 50 Hz

If the hob has a supply cable fitted,

connect it to the mains, using the

colours as a guide (see adjacent

diagram).

Gas connection

The appliance should be connected to the mains

gas supply or to a gas cylinder in compliance with

current national regulations and subsequent

amendments. Before carrying out the connection,

make sure the cooker is compatible with the gas

supply you wish to use. If this is not the case, follow

the instructions indicated in the paragraph

Adapting to different types of gas.

When using liquid gas from a cylinder, install a

pressure regulator which complies with current

national regulations and subsequent amendments.

 Make sure that the gas supply pressure is

consistent with the values indicated in Table 1,

Burner and nozzle specifications. This will ensure

the safe operation and durability of your appliance

while maintaining efficient energy consumption.

Connection with a rigid pipe (copper or steel)

 Connection to the gas system must be carried out

in such a way as not to place any strain of any kind

on the appliance.

There is an adjustable L-shaped pipe fitting on the

appliance supply ramp and this is fitted with a seal

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 67 68

Komentarze do niniejszej Instrukcji

Brak uwag

Whirlpool TEP 649 L Instrukcja Obsługi Strona 17

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Płyty grzewcze Whirlpool TEP 649 L